O prefață
ISO (Organizația Internațională pentru Standardizare) este o alianță globală a organismelor naționale de standardizare (organismele membre ISO). Elaborarea standardelor internaționale se realizează de obicei prin intermediul comitetelor tehnice ISO. Fiecare instituție membră interesată de un subiect pe care a fost înființat un comitet tehnic are dreptul de a fi reprezentată în comitet. În această activitate sunt implicate și organizații internaționale guvernamentale și neguvernamentale care colaborează cu organizațiile de standardizare. ISO lucrează îndeaproape cu Comisia Electrotehnică Internațională (IEC) în toate problemele de standardizare electrică.

International standards are drafted according to the rules given in Part 2 din Directiva ISO/IEC.

Sarcina principală a comitetului tehnic este de a elabora standarde internaționale. Draft international standards adopted by the Technical Committee will be circulated to member bodies for voting. Publicarea ca standard internațional necesită aprobarea de cel puțin 75% a instituţiilor membre.

Vă rugăm să rețineți că anumite conținuturi ale acestui document pot face obiectul drepturilor de brevet. ISO nu este responsabil pentru identificarea vreunuia sau a tuturor acestor drepturi de brevet.

ISO 15181-1 a fost dezvoltat de Comitetul Tehnic ISO/TC 35, Vopsele și lacuri, Subcomisia SC 9, General test methods for paints and varnishes.

ISO 15181-1-2007 “Determinarea vitezei de eliberare a biotoxinelor în vopsele și lacuri vopsele antifouling – Parte 1: Metodă generală de extracție a biotoxinelor”

A doua ediție anulează și înlocuiește prima ediție (ISO 15181-1:2000), which is technically revised, in particular by extending the use of common extraction methods to later parts of ISO 15181.

ISO 15181 constă din următoarele părți, under the general title Paints and varnishes – Determination of fungicide release rates in antifouling coatings:

— Parte 1: General method of extracting fungicides

— Parte 2: Determination of the concentration of copper ions in extracts and calculation of the release rate

— Parte 3: Calculation of the rate of zinc ethylene-bis (dithiocarbamate) (zineb) release by measuring the concentration of ethourea in the extract

— Parte 4: Determination of concentration of pyridine-triphenylborane (PTPB) in extracts and calculation of release rate

— Parte 5: Calculating the release rates of toluenflurane and dichlorofluoraniline by determining the concentrations of dimethyltoluenesulfonamide (DMST) and dimethyltoluenesulfonamide (DMSA) in the extracts

ISO 15181-1-2007 “Determinarea vitezei de eliberare a biotoxinelor în vopsele și lacuri vopsele antifouling – Parte 1: Metodă generală de extracție a biotoxinelor”

Introducere
By using standard conditions for temperature, salinity and pH at low fungicide concentrations in ambient artificial seawater, reproducible values for release rates under specified laboratory conditions can be determined using the method given in this part of ISO 15181, which can be used for quality assurance and material selection purposes. in orice caz, the actual rate of release of fungicides from hull antifouling paints into the environment will depend on many factors, such as vessel operating schedules, years of service, berthing conditions, paint condition, as well as temperature, salinity, pH, pollutants and biota in a particular area.

The results of this test do not reflect the environmental fungicide release rate of antifouling products and are not suitable for direct use in the process of generating environmental risk assessments, generating environmental load estimates, or establishing release rate limits for regulatory purposes. When compared with copper and organotin release rates obtained by direct or indirect measurements of hull copper release rates and measurements on panels exposed in ports, all available data indicate that the results obtained using this general test method substantially overestimate the release rate of fungicides under service conditions. Published results show that for several commercial antifouling coatings, the results of this test method are generally about 10 times or more higher than direct in situ measurements of in-service hull copper and organotin release rates [1,2]. Similar relationships are expected to be found for other fungicides. A realistic estimate of the rate of hull fungicide release under service conditions can only be obtained from this test method if this difference is taken into account.

ISO 15181-1-2007 “Determinarea vitezei de eliberare a biotoxinelor în vopsele și lacuri vopsele antifouling – Parte 1: Metodă generală de extracție a biotoxinelor”

If the results of this testing method are used to generate environmental risk assessments, to produce environmental load estimates, or for regulatory purposes, it is highly recommended to consider the relationship between laboratory release rates and actual environmental inputs in order to more accurately estimate the fungicides release rates of antifouling coatings under real conditions. This can be achieved by applying appropriate correction coefficients [2].

1 Domeniul de aplicare
Această parte a ISO 15181 specifies a general method for the extraction of biocides from antifouling paint films into artificial seawater under specified laboratory conditions. It is used in conjunction with other parts of ISO 15181 to determine the amount of specific fungicides in extracts, for example copper and/or certain organic fungicides, and to be able to calculate the rate of release of these fungicides from paint films under specified laboratory conditions.

2 referințe normative
The following references are required for the application of this document. Pentru referințe datate, se aplică doar versiunea citată. Pentru referințe nedatate, noua versiune a referinței (inclusiv orice revizuiri) se aplică.

ISO 1513, Vopsele și lacuri – Examinarea și pregătirea probelor de testare

ISO 2808, Vopsele și lacuri — Determinarea grosimii peliculei

ISO 3696, analytical laboratory water use – specifications and test methods

ISO 15181-2, vopsele și lacuri — Determination of release rates of fungicides in antifouling coatings — Parte 2: Determination of concentrations of copper ions in extracts and calculation of release rates

ISO 15181-3, Paints and varnishes-Determination of fungicide release rates in antifouling coatings — Parte 3: Calculation of zinc ethylene-bis (dithiocarbamate) (zineb) release rates by determining the concentration of ethylene thiourea in extracts

ISO 15181-1-2007 “Determinarea vitezei de eliberare a biotoxinelor în vopsele și lacuri vopsele antifouling – Parte 1: Metodă generală de extracție a biotoxinelor”

ISO 15181-4, Paints and varnishes-Determination of release rates of fungicides in antifouling coatings – Parte 4: Determination of concentration of pyridine-triphenyl borane (PTPB) in extracts and calculation of release rates

ISO 15181-5, Paints and varnishes-Determination of fungicide release rates in antifouling coatings — Parte 5: Calculation of release rates of toluenflurane and dichlorofluoraniline by determining the concentrations of dimethyltoluenesulfonamide (DMST) and dimethyltoluenesulfonamide (DMSA) in extracts

ISO 15528, Vopsele, lacuri si materii prime pentru vopsele si lacuri – Prelevarea de probe

ASTM D 1141-98 (2003), Standard Practice for Preparing substitute seawater

Doar componenta standard de informații este disponibilă publicului. Pentru a vedea conținutul complet, va trebui să achiziționați standardele prin canale formale.