giriiş
ISO (Uluslararası Standardizasyon Örgütü) ulusal standart kuruluşlarının küresel bir ittifakıdır (ISO üyesi kuruluşlar). Uluslararası standartların geliştirilmesi genellikle ISO teknik komiteleri aracılığıyla yürütülür.. Teknik komite oluşturulmuş bir konu ile ilgilenen her üye kuruluşun o komitede temsil edilme hakkı vardır.. ISO ile irtibat halinde olan uluslararası resmi ve sivil toplum kuruluşları da bu çalışmaya katılıyor. ISO, Uluslararası Elektroteknik Komisyonu ile yakın işbirliği içinde çalışır. (IEC) elektriksel standardizasyonla ilgili tüm konularda.

Uluslararası standartlar Bölüm 1'de verilen kurallara uygun olarak hazırlanmıştır. 3 ISO/IEC Direktifi.

Teknik Komite tarafından kabul edilen uluslararası standart taslağı oylanmak üzere üye kuruluşlara dağıtılacaktır.. Uluslararası bir standart olarak yayın, en azından onay gerektirir 75% üye kuruluşların.

Please note that some elements of this part of ISO 6603 May be the subject of a patent right. ISO bu tür patentlerin herhangi birinin veya tamamının tanımlanmasından sorumlu değildir..

Uluslararası standart ISO 6603-1 was developed by the Technical Committee ISO/TC61, Plastikler, Alt Komite SC 2, Mechanical Properties.

ISO 6603-1-2000 “Plastikler – Sert plastiklerin delinme darbe davranışının belirlenmesi – Parça 1: Enstrümantal olmayan darbe testi”

İkinci baskı, teknik olarak revize edilmiş ilk baskıyı iptal eder ve onun yerine geçer (ISO 6603-1:1985).

ISO 6603 aşağıdaki parçalardan oluşur, under the general heading Plastics – Sert plastiklerin delinme darbe davranışının belirlenmesi:

– Parça 1: Enstrümantal olmayan darbe testi

– Parça 2: Instrumented impact testing

Appendix A of this part of ISO 6603 is for information purposes only.

1 Menzil
This standard specifies a method for determining, under specified conditions, the puncture impact properties of rigid plastics in the form of flat specimens, such as disks or squares. The sample can be molded directly, cut from the sheet or removed from the finished product. Different types of samples and test conditions are defined.

ISO 6603-1-2000 “Plastikler – Sert plastiklerin delinme darbe davranışının belirlenmesi – Parça 1: Enstrümantal olmayan darbe testi”

These drop dart methods are used to study the behavior of plastic films or molds under the impact of a firing pin perpendicular to the specimen plane.

ISO'nun bu kısmı 6603 can be used if it is sufficient to characterize the impact behavior of plastics by an impact failure energy threshold based on many samples. If a force-deflection or force-time plot recorded at a nominal constant firing pin speed is necessary to characterize impact behavior in detail, ISO 6603-2 kullanıldı.

These test methods are suitable for specimens with thicknesses between 1 mm and 4 mm.

Note For thicknesses less than 1 mm, ISO 7765 tavsiye edilir. If the equipment is suitable, it is possible to test thicknesses greater than 4 mm, but this test falls outside the scope of ISO 6603-1 ve ISO 6603-2.

These methods are suitable for the following types of materials:

Rigid thermoplastic molding and extrusion materials, including filled, unfilled and reinforced compounds and sheets;

– Rigid thermosetting molding and extrusion materials, including filling and reinforcing compounds, sheets and laminates;

ISO 6603-1-2000 “Plastikler – Sert plastiklerin delinme darbe davranışının belirlenmesi – Parça 1: Enstrümantal olmayan darbe testi”

Fiber-reinforced thermoset and thermoplastic composites, including unidirectional or non-unidirectional reinforcement materials, such as MATS, woven fabrics, woven roving, cut strands, combined and mixed reinforcement materials, roving, milled fibers and sheets made from pre-impregnated materials (prepregs).

These methods are also applicable to samples molded or machined from finished products, laminates and extruded or cast plates.

The test results are comparable only when the preparation conditions, size and surface of the sample and the test conditions are the same. Özellikle, the results determined on specimens of different thicknesses cannot be compared with each other (see Appendix E: – to ISO 6603-2). A comprehensive assessment of the impact stress response requires measurement of the impact velocity and temperature of different material variables, such as crystallinity and moisture content.

The impact behavior of the finished product cannot be predicted directly from this test, but samples can be taken from the finished product (see above) for testing by these methods.

Test data developed through these methods should not be used in design calculations. Fakat, information on the typical behaviour of the material can be obtained by testing at different temperatures and impact velocities (see Annex D of ISO 6603-2: -), varying thickness (see Annex E of ISO 6603-2: -) and testing samples prepared under different conditions.

ISO'nun bu kısmı 6603 describes two statistical test methods:

– Yöntem A: Staircase Method (Individual) (preferred)

Bu yöntemde, a uniform energy increment is used during the test. After testing each sample, the energy is reduced or increased by uniform increments, depending on the observations (pass or fail) of the previous test.

ISO 6603-1-2000 “Plastikler – Sert plastiklerin delinme darbe davranışının belirlenmesi – Parça 1: Enstrümantal olmayan darbe testi”

– Yöntem B: Group method (İsteğe bağlı)

Bu yöntemde, a continuous group of at least ten samples is tested. The impact failure energy is calculated statistically.

2 Normatif referanslar
The following normative documents contain provisions that, by reference herein, constitute the provisions of this part of ISO 6603. Tarihli referanslar için, any subsequent revisions or amendments to these publications will not apply. Fakat, Parties to agreements based on this part of ISO 6603 are encouraged to investigate the possibility of applying new versions of the following normative documents. Tarihsiz referanslar için, a new version of the standard-setting document referred to applies. ISO and IEC members maintain a register of currently valid international standards.

ISO 291:1997, Plastikler. Adjust and test the standard atmosphere.

ISO 293:1986, Plastikler. Compression forming sample of thermoplastic material.

ISO 294-3:1996, Plastikler. Injection molding of thermoplastic material samples. Parça 3: Small board.

ISO 295:1991, Plastikler. Compression molding of thermosetting material samples.

ISO 1268:19741), Plastikler – Preparation of glass fiber reinforced, resin bonded, low pressure laminates or panels for test purposes.

ISO 2818:1994, Plastikler. The sample was prepared by machining.

ISO 7765-1:1988, plastik filmler ve levhalar. The impact resistance was determined by the free falling dart method. Parça 1: Staircase method.

ISO 7765-2:1994, plastik filmler ve levhalar. The impact resistance was determined by the free fall dart method. Parça 2: Instrumental puncture test.

ISO 6603-1-2000 “Plastikler – Sert plastiklerin delinme darbe davranışının belirlenmesi – Parça 1: Enstrümantal olmayan darbe testi”

3 Terimler ve tanımlar
For the purposes of this part of ISO 6603, aşağıdaki terimler ve tanımlar geçerlidir:

3.1 Genel Bakış

3.1.1 Failure

Any visible breakage of the specimen surface

3.2 Failure standard terms

3.2.1 Crack

Any cracks that are visible to the naked eye and cannot penetrate the entire thickness of the material

See: Figür 1

3.2.2 Broken

Any cracks throughout the entire thickness of the material

See: Figür 2

3.2.3 Penetration

Failure of the firing pin to penetrate the entire thickness of the specimen

See: Figür 3 B)

3.2.4 Grinding

Break the sample into two or more pieces

See: Figür 3 A)

3.3 Impact failure items
3.3.150 % impact failure energy E50

The energy that causes 50% of the sample to fail, as defined in 3.1.1

3.3.250 % impact failure mass M50

The mass that causes 50% of the sample to fail at a given fall height, as defined in 3.1.1

3.3.350 % impact failure mass H50

50% impact failure height H50 uses the height at which a given falling mass causes 50% sample failure, as defined in 3.1.1

Figür 1 – Specimen sections damaged by “cracks” [B) and c) after bending by hand

ISO 6603-1-2000 “Plastikler – Sert plastiklerin delinme darbe davranışının belirlenmesi – Parça 1: Enstrümantal olmayan darbe testi”

Figür 2 – Slices passed through the specimen are damaged by “breakage” [B) and c) after bending by hand

Figür 3 – Examples of “broken” failures [A) Ve “penetrated” [B)

A)

B)

Yalnızca standart bilgi bölümü herkese açıktır. İçeriğin tamamını görmek için, standardı resmi kanallardan satın almanız gerekiyor.