Анотація

This specification covers film, paper and cloth types of pressure sensitive tape and is applied to packaging, box LIDS and seals. This specification covers five types of tape: водонепроникний, weather-resistant, polyester-supported tape (Тип I), water-resistant polyester-supported tape (Type II), water-resistant polypropylene supported tape (Type III), water-resistant woven fabric straps (Type IV) and weather-resistant paper straps. Tape should be manufactured using film, paper or cloth as backing and coated with a smooth and evenly distributed layer of pressure-sensitive water-insoluble adhesive. The tape should be rolled over the paper fiber or plastic core, and should be free of defects, and the edge should be clean, straight and unbroken. Test adhesion, міцність на розрив, tear resistance, товщина, water permeability,

This summary is a brief summary of the reference standards. It is informational only and not a formal part of the standard; The full text of the standard itself needs to be used and applied for reference. ASTM provides no warranties, явні чи неявні, і не означає, що зміст цієї анотації є точним, complete, or new.

Крок 1: Область застосування

1.1 This specification covers film, paper and cloth pressure sensitive tape for box closure and sealing.

1.2 Values expressed in inch-pounds or SI units shall be treated as standards separately. The values specified in each system may not be exactly the same; тому, each system needs to be used independently and the values cannot be combined in any way.

1.3 The following safety hazard warnings apply only to Section 14 “Test Methods” of this specification. Цей стандарт не призначений для вирішення всіх проблем безпеки, пов’язаних з його використанням. Користувачі цього стандарту несуть відповідальність за встановлення належної безпеки, специфікації щодо здоров’я та навколишнього середовища, а також для визначення застосовності нормативних обмежень перед використанням.

1.4 Цей міжнародний стандарт базується на міжнародно визнаних принципах стандартизації, встановлених у Рішенні про принципи розробки міжнародних стандартів, Настанови та рекомендації, видані СОТ щодо технічних бар'єрів у торгівлі (TBT) Комітет.

ASTM D5486/D5486M-2020 “Standard Specification for Pressure Sensitive Tapes for Packaging, Box LIDS and Seals”

2. Зверніться до файлу

Federal regulation

FED-STD-595

PPP-T-60 Tape: Packaged, waterproof available from the Standardization document ordering desk Bldg. 4 D Block, 700 Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS.

TAPPI standard

Internal Tear Resistance of T 414 папір (Elmendorf-type method) is available from the Pulp and Paper Industries Association (TAPPI), 15 Technology Parkway South, Norcross, GA 30092, http:// www.tappi.org.

Стандарт ASTM

D996 Packaging and distribution environmental terms

D1974 Practice of methods for sealing, sealing and reinforcing fiberboard boxes

D2860 / D2860M Test method for bonding pressure-sensitive tape to fiberboard at a 90 degree Angle and under constant stress

Test method for peel adhesion of D3330 / D3330M pressure sensitive tape

D3611 pressure sensitive tape accelerated aging practice

Test method for thickness of D3652 / D3652M pressure sensitive tape

Test method for shear adhesion of D3654 / D3654M pressure sensitive tape

D3715 / D3715M pressure sensitive tape quality assurance practice

Test method for breaking strength and elongation of D3759 / D3759M pressure sensitive tape

Test method for unwinding force of D3811 / D3811M pressure sensitive tape

D3815 / D3815M Practice of accelerating weathering of pressure sensitive tape through open flame carbon arc exposure equipment

Test method for water permeability of D3816 / D3816M pressure sensitive tape

Test method for water vapor transmittance of D3833 / D3833M pressure sensitive tape

D3951 Commercial packaging specification

D4727 / D4727M Specification for corrugated and solid fiberboard sheets (container grade) and cut shapes

D5570 used as a test method for water resistance of tapes and adhesives for box covers