ايزو 23559-2011 دليل لاختبار الأفلام البلاستيكية والأفلام البلاستيكية الحرارية
مقدمة
ايزو (المنظمة الدولية للمقاييس) هو الاتحاد العالمي لهيئات المعايير الوطنية (الهيئات الأعضاء في منظمة الأيزو). عادة ما يتم تطوير المعايير الدولية من خلال اللجان الفنية ISO. يحق لكل مجموعة أعضاء مهتمة بموضوع تم إنشاء لجنة فنية بشأنه أن تكون ممثلة في اللجنة. دولي, وتشارك أيضًا المنظمات الحكومية وغير الحكومية المتعاونة مع ISO في هذا العمل. تعمل ISO بشكل وثيق مع اللجنة الكهروتقنية الدولية (اللجنة الانتخابية المستقلة) في جميع المسائل المتعلقة بالتوحيد الكهربائي.
تتم صياغة المعايير الدولية وفقًا للقواعد الواردة في الجزء 2 لتوجيهات ISO/IEC.
The main task of the technical committee is to set international standards. وسيتم توزيع مشروع المعايير الدولية الذي اعتمدته اللجنة الفنية على الهيئات الأعضاء للتصويت عليه. يتطلب النشر كمعيار دولي الموافقة بتصويت على الأقل 75% من جسم العضو.
يرجى ملاحظة أن بعض عناصر هذه الوثيقة قد تكون موضوع حقوق براءات الاختراع. ISO ليست مسؤولة عن تحديد أي أو كل براءات الاختراع هذه.
ايزو 23559 was developed by the Technical Committee ISO/TC 61, البلاستيك, اللجنة الفرعية SC 11, منتجات.
This second edition cancels and replaces the first edition (ايزو 23559:2007) by slightly revising the first edition (ايزو 23559:2007) by introducing an additional specimen (for low strain) for the tensile impact test specified in Table 2.
ايزو 23559-2011 دليل لاختبار الأفلام البلاستيكية والأفلام البلاستيكية الحرارية
يقدم
This international standard is intended to provide manufacturers and users with guidance for testing plastic film.
Although existing standards provide this guidance for many thin film products, they are very specific in terms of the materials covered and do not address many commercial films produced as mixtures or multilayer structures. في بعض الحالات, existing standards are limited to a single process technology for producing thin films.
It is also recognized that the general standardized concept of film sample preparation is not currently realistic due to the numerous commercial processes used to produce films and the different processing parameters required for different materials, mixtures and/or structures. على الجانب الآخر, it is possible to standardize sample preparation for clearly defined materials and manufacturing processes, but this is not within the scope or intent of this document.
Safety Statement – Persons using this document should be familiar with normal laboratory practices (إذا كان قابلا للتطبيق). This document is not intended to address all security concerns, لو اي, المرتبطة باستخدامه. It is the user’s responsibility to establish appropriate safety and health practices and ensure compliance with any regulatory requirements.
ايزو 23559-2011 دليل لاختبار الأفلام البلاستيكية والأفلام البلاستيكية الحرارية
1 نطاق التطبيق
This international standard identifies specific testing procedures to assist manufacturers and users in selecting and characterizing single – or multilayer thermoplastic films. It aims to provide a guide for films that do not have existing standards or specifications.
Note Due to the range of materials used and the variety of processes that can be used to produce various thin film structures, sample preparation is not covered in this document.
If an international standard exists for a particular film product, the requirements of that standard shall take precedence over this document.
There are many national, regional, and industry standards that address application-specific requirements. Since this international standard is intended to provide general guidance it is not within the scope of addressing these issues.
The importance and applicability of the data should be determined by the user.
2 الملفات المرجعية المعيارية
The following reference files are required for the application of this file. للمراجع المؤرخة, تنطبق إصدارات الاقتباس فقط. بالنسبة للاقتباسات غير المؤرخة, the most recent version of the referenced document (including any amendments) ينطبق.
ايزو 307, البلاستيك – polyamides – Determination of viscosity values
ايزو 527-3, البلاستيك – Determination of tensile properties – جزء 3: Test conditions for films and sheets
ايزو 1133-1, البلاستيك – Determination of melt mass flow (MFR) ويذوب تدفق الحجم (MVR) of thermoplastics – جزء 1: Standard method
ايزو 1183-1, البلاستيك – Determination of the density of non-foamed plastics – جزء 1: immersion method, liquid gravity flask method and titration method
ايزو 1183-2, البلاستيك – Determination of the density of non-foamed plastics – جزء 2: density gradient column method
ايزو 1183-3, البلاستيك – Determination of the density of non-foamed plastics – جزء 3: Gas specific gravity flask method
ايزو 2813, الدهانات والورنيشات – Determination of the specular gloss of 20°, 60° و85° أفلام طلاء غير معدنية
ايزو 4589-1, البلاستيك – Determination of combustion behaviour by oxygen index – جزء 1: Guide
ايزو 4589-2, البلاستيك — Determination of combustion behaviour by oxygen index — جزء 2: ambient temperature test
ايزو 4592, البلاستيك – films and sheets – determination of length and width
ايزو 4593, البلاستيك – films and sheets – Determination of thickness by mechanical scanning
ايزو 6383-1, البلاستيك – films and sheets – Determination of tearing resistance – جزء 1: pant type tearing method
ايزو 6383-2, البلاستيك – films and sheets – Determination of tearing resistance – جزء 2: Elmendorf method
ايزو 7765-1, plastic films and sheets – Determination of impact resistance by the free-fall method – جزء 1: طريقة الخطوة
ايزو 7765-2, Plastic films and sheets – Determination of impact resistance by the free fall method – جزء 2: Instrumental puncture test
ايزو 8256, البلاستيك – Determination of tensile impact strength
ايزو 8295, البلاستيك – films and sheets – Determination of coefficient of friction
ايزو 8296, البلاستيك – films and sheets – determination of wetting tension
ايزو 9773, البلاستيك – Determination of the combustion behaviour of thin flexible vertical specimens in contact with a small flame ignition source
ايزو 11357-2, البلاستيك — Differential scanning calorimetry (DSC) — جزء 2: Determination of glass transition temperature
ايزو 11357-3, البلاستيك — Differential scanning calorimetry (DSC) — جزء 3: Determination of melting and crystallization temperature and enthalpy
– ايزو 11443, البلاستيك – Determination of the fluidity of plastics using capillaries and slit die head rheometers
ايزو 11501, البلاستيك – films and sheets – Determination of dimensional changes in heating
ايزو 11502, البلاستيك – films and sheets – Determination of adhesion resistance
ايزو 13468-1, البلاستيك – Determination of total light transmittance of transparent materials – جزء 1: single beam instrument
ايزو 13468-2, البلاستيك — Determination of total light transmittance of transparent materials — جزء 2: Double beam instrument
ايزو 14782, البلاستيك — determination of fog in transparent materials
ايزو 15105-1, البلاستيك – films and sheets – Determination of gas transmittance – جزء 1: differential pressure method
ايزو 15105-2, البلاستيك – films and sheets – Determination of gas permeability – جزء 2: isobaric method
ايزو 15106-1, البلاستيك – films and sheets – Determination of water vapour transmittance – جزء 1: Humidity detection sensor method
ايزو 15106-2, البلاستيك – films and sheets – Determination of water vapour transmittance – جزء 2: Infrared detection sensor method
ايزو 15106-3, البلاستيك – films and sheets – Determination of water vapour transmittance – جزء 3: electrolytic detection sensor method
ايزو 15989, البلاستيك – films and sheets – Measurement of water contact angles for corona treated films
اللجنة الانتخابية المستقلة 60093, Test method for volume and surface resistivity of solid electrical insulating materials
اللجنة الانتخابية المستقلة 60112, Verification and comparison of solid insulating materials – Determination of leakage trace index
اللجنة الانتخابية المستقلة 60243-1, Electrical strength of insulating materials – Test methods – جزء 1: power frequency test
اللجنة الانتخابية المستقلة 60250, recommended method for determining the dielectric constant and dielectric loss factor of electrical insulating materials at power, audio and radio frequencies (including meter wavelengths)
أستم D882, Standard Test Method for Tensile Properties of Thin plastic Sheets
ASTM D5458, Standard Test method for Peel Adhesion of Stretched Packaging Film
ASTM D5459, Standard Test Method for Longitudinal Elastic Recovery and Permanent Deformation and Stress Retention of Stretched Packaging Films
ASTM D5748, Standard Test method for Resistance to Protruding Puncture of Stretched Packaging films
ASTM F88, Standard Test Method for Seal Strength of Flexible Barrier Materials
ASTM F1921, Standard Test Method for Thermal Sealing Strength (Thermal Viscosity) of Thermoplastic polymers and Blends Containing Flexible Web Sealing Surfaces
3 المصطلحات والتعاريف
لأغراض هذه الوثيقة, تنطبق المصطلحات والتعاريف التالية.
3.1 Thin Film
Films of nominal thickness not greater than 0.25 مم
ملاحظة الدخول 1: Although not specifically defined in ISO 472, the 0.25mm limit is noted. ASTM D883 specifically defines thin films as ≤ 0.25mm.
ملحوظة 2 Sheets with nominal thickness greater than 0.25mm May be too hard to use a test method more suitable for thinner structures.
قسم المعلومات القياسية فقط هو العام. لرؤية المحتوى كاملا, تحتاج إلى شراء المعيار من خلال القنوات الرسمية.