předmluva
ISO (Mezinárodní organizace pro normalizaci) je globální federací národních normalizačních orgánů (členy ISO). Vývoj mezinárodních norem se obvykle provádí prostřednictvím technických komisí ISO. Každá členská skupina, která se zajímá o předmět, pro který byla ustavena technická komise, má právo být v komisi zastoupena. Mezinárodní, Do této práce jsou zapojeny také vládní a nevládní organizace ve spolupráci s ISO. ISO úzce spolupracuje s Mezinárodní elektrotechnickou komisí (IEC) ve všech záležitostech elektrické normalizace.

Část 1 Směrnice ISO/IEC popisuje postupy použité pro vývoj tohoto dokumentu a pro další údržbu. Zejména, všimněte si různých schvalovacích norem vyžadovaných pro různé typy dokumentů ISO. Tento dokument byl vypracován v souladu s redakčními pravidly v Části 2 směrnice ISO/IEC (viz iso.org/directives).

Upozorňujeme, že některé prvky tohoto dokumentu mohou být předmětem patentových práv. ISO nenese odpovědnost za identifikaci některého nebo všech takových patentů. Podrobnosti o jakýchkoli patentových právech zjištěných během procesu vývoje dokumentace budou zahrnuty v úvodu a/nebo seznamu obdržených patentových nároků ISO (viz iso.org/patents).

Jakékoli obchodní názvy použité v tomto dokumentu jsou informace poskytnuté pro pohodlí uživatele a nepředstavují podporu.

Explanations of the relevant standards of voluntary, ISO specific terms related to conformity assessment and the expression of meaning, and the ISO in the technical barriers to trade (TBT) dodržovat principy světové obchodní organizace (WTO) information, please refer to the iso.org/iso/foreword.html.

This document has been prepared by ISO/TC 206 Technical Committee on Fine Ceramics.

Any feedback or questions on this document should be referred to the user’s national standards body. A complete list of these institutions can be found at iso.org/members.html.

ISO 23737-2021 “Jemná keramika (Advanced ceramics, pokročilá technická keramika) – Methods for evaluating the wear and friction characteristics of fine ceramic films under wet and dry conditions”

představit
Fine ceramic films are used in a variety of applications, such as sensors, actuators or other micromechanical components; Display element; Memory element; Recording media; Optical element; Packaging film; And films and glass for buildings and vehicles. In the industrial application of fine ceramic films, wear resistance is an important index for evaluation. The wear resistance of fine ceramic films is greatly affected by the ambient humidity and the humidity history of the films. Fine ceramic films are also used in different humidity environments where criteria are required to evaluate wear resistance and friction coefficient over a wide humidity range. The standards published to date for wear resistance testing only assume a temperature environment of 23 °C and a relative humidity of 50 %. The thickness of the film to be measured is also relatively large, with a few to 10μm. These test procedures are not suitable for evaluating the wear resistance of fine ceramic films with thickness up to approximately 1 µm for use in electronic and optical devices because the wear resistance of small indentation loads is affected by the relative humidity of the test environment, tj. the mechanism used in the wear testing of fine ceramic films with small indentation loads is strongly affected by the relative humidity of the test environment. Proto, the wear test of fine ceramic film should be carried out under the specified relative humidity conditions. This document provides measurements that help accurately assess the wear resistance of fine ceramic films, up to a thickness of approximately 1 um, deposited on thin substrates or organic polymer films, in dry and high humidity environments. The present document has been developed to facilitate industrial development through the rapid dissemination of these measurements.

1 Rozsah použití
This document specifies a method for testing the wear resistance and friction coefficient of fine ceramic films in dry and high humidity environments, where such films may be up to approximately 1 µm thick and deposited on a substrate or base, including thin or very thin organic polymer film substrates.

2 Normativní referenční soubory
When the following documents are referenced in the context, part or all of them constitute the requirements of this document. Pro datované odkazy, platí pouze citační verze. Pro nedatované citace, nejnovější verzi odkazovaného dokumentu (včetně případných změn) platí.

ISO 3274, Geometric Product Specification (GPS) – Surface texture: section method – Nominal characteristics of contact (stylus) nástroje

ISO 13565-1, Geometric Product Specification (GPS) – Surface Texture: Section method Surfaces with layered functional properties – Část 1: filtration and general measurement conditions

ISO 13565-2, Geometric Product Specification (GPS) – Surface Texture: Section method Surfaces with layered functional properties – Část 2: Characterization of heights using linear material ratio curves

ISO 20507, Jemná keramika (Advanced ceramics, pokročilá technická keramika) — Slovní zásoba

3 Termíny a definice
Pro účely tohoto dokumentu, termíny a definice uvedené v ISO 20507 a níže platí.

3.2 Friction force

The resistance exerted on a relative body when objects in contact move or tend to slide against each other

3.3 Friction coefficient

The dimensionless ratio of friction to the applied normal force

3.4 Wear test

Tests for the evaluation of friction and wear characteristics caused by sliding contact motion

Poznámka 1: In a narrow sense, the term “wear test” refers to the process by which wear occurs on the specimen as a result of sliding motion; In broad terms, it means processes such as sample preparation, wear formation, friction coefficient measurement, and evaluation of wear trajectoryand wear parts formed on the inverse material.

3.5 Drying Chamber

A sealed container for removing moisture from the surface of the sample while the sample is kept in a vacuum

3.6 Relativní vlhkost

Ratio of partial vapor pressure to saturated vapor pressure at a given temperature

3.7 Dry air

Air with a dew point of −60 °C or lower at an absolute pressure of 101.3 kPa

3.8 Dry Nitrogen

At an absolute pressure of 101.3 kPa, the dew point is −60 °C or lower nitrogen

Veřejná je pouze standardní informační sekce. Chcete-li zobrazit celý obsah, you will need to purchase the standard through the official channels.