paunang salita
ISO (International Organization para sa Standardisasyon) ay ang pandaigdigang pederasyon ng mga pambansang pamantayan ng katawan (Mga katawan ng miyembro ng ISO). Ang pagbuo ng mga internasyonal na pamantayan ay karaniwang isinasagawa sa pamamagitan ng ISO teknikal na komite. Each member group interested in a subject on which a technical committee has been established has the right to be represented on the Committee. International, governmental and non-governmental organizations in liaison with ISO are also involved in this work. ISO ay gumagana nang malapit sa International Electrotechnical Commission (IEC) sa lahat ng bagay ng electrical standardization.

Bahagi 1 ng ISO / IEC Directive ay naglalarawan ng mga pamamaraan na ginamit upang bumuo ng dokumentong ito at para sa karagdagang pagpapanatili. Sa partikular na, tandaan ang iba't ibang mga pamantayan sa pag apruba na kinakailangan para sa iba't ibang uri ng mga dokumento ng ISO. This document has been drafted in accordance with the editorial rules in Part 2 ng Direktiba ng ISO / IEC (tingnan iso.org/directives).

Mangyaring tandaan na ang ilang mga elemento ng dokumentong ito ay maaaring maging paksa ng mga karapatan sa patent. Ang ISO ay hindi mananagot para sa pagtukoy ng anuman o lahat ng naturang patente. Details of any patent rights identified during the documentation development process will be included in the introduction and/or list of ISO patent claims received (tingnan iso.org/patents).

Ang anumang mga pangalan ng kalakalan na ginamit sa dokumentong ito ay impormasyong ibinigay para sa kaginhawahan ng gumagamit at hindi bumubuo ng isang endorsement.

Mga paliwanag sa mga kaugnay na pamantayan ng boluntaryong, ISO tiyak na mga termino na may kaugnayan sa pag alinsunod pagtatasa at ang pagpapahayag ng kahulugan, at ang ISO sa mga teknikal na hadlang sa kalakalan (TBT) sumunod sa prinsipyo ng world trade organization (WTO) impormasyon, paki refer po sa iso.org/iso/foreword.html.

This document has been prepared by ISO/TC 206 Technical Committee on Fine Ceramics.

Anumang feedback o mga katanungan sa dokumentong ito ay dapat na tinutukoy sa pambansang pamantayan ng katawan ng gumagamit. Ang kumpletong listahan ng mga institusyong ito ay matatagpuan sa iso.org/members.html.

ISO 23737-2021 “Fine Ceramics (Advanced ceramics, advanced technical ceramics) – Methods for evaluating the wear and friction characteristics of fine ceramic films under wet and dry conditions”

ipakilala ang
Fine ceramic films are used in a variety of applications, such as sensors, actuators or other micromechanical components; Display element; Memory element; Recording media; Optical element; Packaging film; And films and glass for buildings and vehicles. In the industrial application of fine ceramic films, wear resistance is an important index for evaluation. The wear resistance of fine ceramic films is greatly affected by the ambient humidity and the humidity history of the films. Fine ceramic films are also used in different humidity environments where criteria are required to evaluate wear resistance and friction coefficient over a wide humidity range. The standards published to date for wear resistance testing only assume a temperature environment of 23 °C and a relative humidity of 50 %. The thickness of the film to be measured is also relatively large, with a few to 10μm. These test procedures are not suitable for evaluating the wear resistance of fine ceramic films with thickness up to approximately 1 µm for use in electronic and optical devices because the wear resistance of small indentation loads is affected by the relative humidity of the test environment, i.e. the mechanism used in the wear testing of fine ceramic films with small indentation loads is strongly affected by the relative humidity of the test environment. Kaya nga, the wear test of fine ceramic film should be carried out under the specified relative humidity conditions. This document provides measurements that help accurately assess the wear resistance of fine ceramic films, up to a thickness of approximately 1 M, deposited on thin substrates or organic polymer films, in dry and high humidity environments. The present document has been developed to facilitate industrial development through the rapid dissemination of these measurements.

1 Saklaw ng aplikasyon
This document specifies a method for testing the wear resistance and friction coefficient of fine ceramic films in dry and high humidity environments, where such films may be up to approximately 1 µm thick and deposited on a substrate or base, including thin or very thin organic polymer film substrates.

2 Normative reference files
When the following documents are referenced in the context, part or all of them constitute the requirements of this document. Para sa mga petsang sanggunian, angkop ang mga bersyon na may pagbanggit lamang. Para sa mga walang petsang pagbanggit, the most recent version of the referenced document (including any amendments) angkop.

ISO 3274, Geometric Product Specification (GPS) – Surface texture: section method – Nominal characteristics of contact (stylus) mga instrumento

ISO 13565-1, Geometric Product Specification (GPS) – Surface Texture: Section method Surfaces with layered functional properties – Bahagi 1: filtration and general measurement conditions

ISO 13565-2, Geometric Product Specification (GPS) – Surface Texture: Section method Surfaces with layered functional properties – Bahagi 2: Characterization of heights using linear material ratio curves

ISO 20507, Fine Ceramics (Advanced ceramics, advanced technical ceramics) — Bokabularyo

3 Mga Tuntunin at Kahulugan
Para sa mga layunin ng dokumentong ito, ang mga termino at kahulugan na ibinigay sa ISO 20507 and below apply.

3.2 Friction force

The resistance exerted on a relative body when objects in contact move or tend to slide against each other

3.3 Friction coefficient

The dimensionless ratio of friction to the applied normal force

3.4 Wear test

Tests for the evaluation of friction and wear characteristics caused by sliding contact motion

Tala 1: In a narrow sense, the term “wear test” refers to the process by which wear occurs on the specimen as a result of sliding motion; In broad terms, it means processes such as sample preparation, wear formation, friction coefficient measurement, and evaluation of wear trajectoryand wear parts formed on the inverse material.

3.5 Drying Chamber

A sealed container for removing moisture from the surface of the sample while the sample is kept in a vacuum

3.6 Relative Humidity

Ratio of partial vapor pressure to saturated vapor pressure at a given temperature

3.7 Dry air

Air with a dew point of −60 °C or lower at an absolute pressure of 101.3 kPa

3.8 Dry Nitrogen

At an absolute pressure of 101.3 kPa, the dew point is −60 °C or lower nitrogen

Ang standard information section lamang ang pampubliko. Upang makita ang buong nilalaman, you will need to purchase the standard through the official channels.