ISO 7590-2018 “חגורות שינוע של חבל תיל – שיטות קביעה לעובי כולל ועובי חיפוי”

הקדמה
ISO (הארגון הבינלאומי לתקינה) היא ברית גלובלית של גופי תקינה לאומיים (גופים חברי ISO). פיתוח תקנים בינלאומיים מתבצע בדרך כלל באמצעות ועדות טכניות של ISO. כל מוסד חבר המעוניין בנושא בו הוקמה ועדה טכנית זכאי להיות מיוצג בוועדה. ארגונים בינלאומיים ממשלתיים ובלתי-ממשלתיים העוסקים בקשר עם ארגוני תקינה מעורבים אף הם בעבודה זו. ISO עובד בשיתוף פעולה הדוק עם הנציבות האלקטרוטכנית הבינלאומית (חברת החשמל) בכל הקשור לתקינה חשמלית.

ההליכים המשמשים לפיתוח מסמך זה וכן אלה המשמשים לתחזוקה נוספת מתוארים בחלק 1 של הוראת ISO/IEC. באופן מיוחד, יש לשים לב לקריטריוני האישור השונים הנדרשים עבור סוגים שונים של מסמכי ISO. מסמך זה נוסח בהתאם לכללי העריכה של חלק 2 של הוראת ISO/IEC (ראה iso.org/directives).

אנא שימו לב כי תוכן מסוים של מסמך זה עשוי להיות כפוף לזכויות פטנט. ISO אינה אחראית לזיהוי כל זכויות פטנט כאלה או כולן. Details of any patent rights identified during the development of the document will be in the introduction and/or in the ISO list of patent claims received (ראה iso.org/patents).

כל שמות מסחריים המשמשים במסמך זה מסופקים כמידע לנוחות המשתמש ואינם מהווים אישור.

ISO 7590-2018 “חגורות שינוע של חבל תיל – שיטות קביעה לעובי כולל ועובי חיפוי”

מִרָצוֹן, related standards and conformity assessment related ISO specific and express the meaning of terminology as well as in relevant ISO technical barriers to trade (TBT) adhere to the principle of the world trade organization (WTO) מֵידָע, אנא עיין בכתובת האתר הבאה:iso.org/iso/foreword.html.

This document was prepared by Technical Committee ISO/TC 41, Pulleys and Belts (including V-belts), ועדת המשנה SC 3, Conveyor Belts.

The sixth edition cancels and replaces the technically revised fifth edition (ISO 7590:2009). Compared with the previous edition, the main changes are as follows:

Figure 4 has been corrected.

ISO 7590-2018 “חגורות שינוע של חבל תיל – שיטות קביעה לעובי כולל ועובי חיפוי”

1 תְחוּם
This document specifies three methods for measuring the total thickness and cover thickness of steel cord conveyor belts.

Methods A1 and A2 (micrometer method) can be used for all steel cord conveyor belts to measure total belt thickness and overlay thickness.

שיטה ב' (optical method) is only used to measure cover thickness. If there is textile or metal weft, it is also not suitable for the end of the wire rope to twist when cutting.

2 אזכור נורמטיבי
There is no normative reference in this document.

ISO 7590-2018 “חגורות שינוע של חבל תיל – שיטות קביעה לעובי כולל ועובי חיפוי”

3 מונחים והגדרות
למטרות מסמך זה, המונחים וההגדרות הבאים חלים.

ISO וחברת החשמל מחזיקות מאגרי מינוח לתקינה בכתובות הבאות:

– פלטפורמת גלישה מקוונת ISO: זמין בכתובת iso.org/obp

IEC Electronic Encyclopedia: זמין באתר electropedia.org/

3.1 Circuit breaker
The lateral reinforcement material in the conveyor belt, usually made of textile material, is inserted above and below or above or below the wire rope at a distance of at least 1 mm and is considered as part of the lid

הערה 1: It is used to protect longitudinal ropes from material damage caused by impact or jam.

3.2 Fabric
The transverse parts of the protective reinforcement of the steel cord or textile cord, usually inserted above and below the steel cord, or above or below, at a distance of less than 1 מ"מ, are considered to be part of the conveyor belt body

רק רכיב המידע הסטנדרטי זמין לציבור. לצפייה בתוכן המלא, תצטרך לרכוש את התקנים דרך ערוצים רשמיים.

שתף את הפוסט