ISO 26424-2008 “ファインセラミックス (先進的なセラミックス, 先進的なテクニカルセラミックス) 顕微鏡摩耗試験によるコーティングの耐摩耗性の決定”
導入
ISO (国際標準化機構) 国家標準化団体の世界的な同盟です (ISO会員団体). 国際規格の開発は通常、ISO 技術委員会を通じて行われます。. 技術委員会が設立された主題に関心を持つ各加盟機関は、その委員会に代表される権利を有する。. ISO と連携する国際政府および非政府組織もこの作業に関与しています。. ISO は国際電気標準会議と緊密に連携しています。 (IEC) 電気の標準化に関するあらゆる問題について.
国際規格は、第 1 部に記載されている規則に従って草案されます。 2 ISO/IEC 指令の.
技術委員会の主な任務は国際標準を開発することです. 技術委員会によって採択された国際規格草案は、投票のために加盟団体に配布されます。. 国際標準として発行するには、少なくとも承認が必要です 75% 加盟機関の.
この文書の特定の要素は特許権の対象となる場合があることに注意してください。. ISO は、そのような特許の一部またはすべてを特定する責任を負いません。.
ISO 26424-2008 “ファインセラミックス (先進的なセラミックス, 先進的なテクニカルセラミックス) 顕微鏡摩耗試験によるコーティングの耐摩耗性の決定”
ISO 26424 was developed by the Technical committee ISO/TC 206 for Fine Ceramics.
1 範囲
This standard specifies a method for measuring abrasive wear rates for ceramic coatings through microscopic wear tests based on the well-known shrinkage grinding technique used for coating thickness determination in ISO 26423[11].
The method can provide data on coating and substrate wear rates by performing two separate tests or by carefully analyzing data from a single test series.
The method can be applied to samples with flat or non-flat surfaces, but the analysis of results described in Article 9 applies only to flat samples. For non-planar samples, a more complex analysis is required and may require the use of numerical methods.
2 規範的参照
The following reference files are difficult or lacking for the use of this document. 日付の付いた参照については, 引用されたバージョンのみが適用されます. 日付のない参考文献については, リファレンスの新しいバージョン (改訂も含めて) 当てはまる.
ISO 3290-1, Rolling bearings – Balls – 一部 1: Steel balls
ISO/IEC 17025, General requirements for testing and calibration laboratory competence
3 用語と定義
この文書の目的のために, 次の用語と定義が適用されます.
3.1 Abrasive wear rate
Abrasive wear coefficient K
The volume of material removed per unit of sliding distance at a normal contact load of 1 N
ISO 26424-2008 “ファインセラミックス (先進的なセラミックス, 先進的なテクニカルセラミックス) 顕微鏡摩耗試験によるコーティングの耐摩耗性の決定”
標準情報部分のみ公開. 完全なコンテンツを表示するには, 公式チャネルを通じて標準を購入する必要があります.