의미와 목적
3.1 A number of laboratory procedures are used to evaluate the effectiveness of flame retardant and refractory treatments and coatings. 일반적으로, these methods measure three stages of fire development: (1) ignition; (2) Flame spread (the growth rate of the fire); (3) Fire extent. While all three are extremely important, flame spread has been recognized as a major factor relevant for testing flame retardant coatings.

3.2 Flame spread rating based on test method E84 has gained general acceptance from regulatory authorities, but such large-scale testing is rarely practical during the development or modification of flame retardant-based coatings.

3.3 The test method provides the relative flame spread of the experimental coating using small specimens under conditions established in a 2-foot tunnel. By experimentally calibrating 2-foot tunnels with a similar test method E84 grade flame retardant paint, the results obtained from this test method can be used to screen the suitability of the coating for testing in test method E84 tunnels.

3.3.1 The test method is intended as an experimental tool for evaluating experimental coatings for further development. The results of this test method are not directly related to, or implied by, the results of the test method E84 tunnel.

3.3.2 The results obtained by this test method cannot by itself be used as an accurate predictor of the performance in test method E84 and shall not be used to certify any class of flame spread performance.

ASTM D 3806-98-2019 “난연성 코팅의 소규모 평가 (2-발 터널 방법)”

범위
1.1 This test method determines the protection provided by the coating to its substrate and the comparative combustion characteristics of the coating by assessing the flame spread over the surface during ignition under controlled conditions in a small tunnel. This sets the stage for comparing the surface combustion characteristics of different coatings without specifically considering all end-use parameters that may affect the surface combustion characteristics under real fire conditions.

1.2 In addition to the experimental flame spread rate, panel weight consumed, time of combustion and afterglow, coke size and index, and expansion height can also be measured in this test. 하지만, a relationship between these measures should not be assumed.

1.3 This standard is used to determine certain fire test responses of materials, products or components to heat and flame under controlled conditions by using results obtained from fire test response standards. The results obtained using this standard do not in themselves constitute a measure of fire hazard or fire risk.

1.4 SI 단위로 표현된 값은 표준으로 간주되어야 합니다.. 괄호 안의 값은 참고용입니다..

1.5 This standard is used to measure and describe the reaction of materials, products or components to heat and flame under controlled conditions, but does not in itself contain all the factors required for fire hazard or fire risk assessment of materials, products or components under actual fire conditions.

ASTM D 3806-98-2019 “난연성 코팅의 소규모 평가 (2-발 터널 방법)”

1.6 Fire testing is inherently dangerous. Appropriate personnel and property protection measures should be taken when these tests are carried out.

1.7 이 표준은 모든 안전 문제를 다루기 위한 것이 아닙니다., 만약에 어떠한, 그 사용과 관련된. 적절한 안전을 확립하는 것은 이 표준 사용자의 책임입니다., 건강 및 환경 관행을 확인하고 사용 전 규제 제한의 적용 여부를 결정합니다..

1.8 본 국제 표준은 국제 표준 개발 원칙에 관한 결정에서 확립된 국제적으로 인정받는 표준화 원칙에 따라 개발되었습니다., 세계무역기구(WTO) 무역기술장벽위원회가 발행한 지침 및 권고사항.