ISO 23559-2011 – Testgids voor plastic films en thermoplastische films
invoering
ISO (Internationale Organisatie voor Standaardisatie) is een mondiale federatie van nationale normalisatie-instellingen (ISO-lidorganisaties). De ontwikkeling van internationale normen wordt doorgaans uitgevoerd via technische ISO-commissies. Elke ledengroep die geïnteresseerd is in een onderwerp waarvoor een technische commissie is opgericht, heeft het recht om in de commissie vertegenwoordigd te zijn. Internationale organisaties, regeringen en niet-gouvernementele organisaties die in contact staan met ISO zijn ook bij dit werk betrokken. ISO werkt nauw samen met de Internationale Elektrotechnische Commissie (IEC) over alle kwesties van elektrische standaardisatie.
Internationale normen worden opgesteld in overeenstemming met de regels gegeven in Deel 2 van de ISO/IEC-richtlijn.
De belangrijkste taak van de technische commissie is het ontwikkelen van internationale normen. Het ontwerp van de internationale norm dat door de Technische Commissie is aangenomen, zal ter stemming onder de aangesloten organen worden verspreid. Publicatie als internationale standaard vereist goedkeuring met ten minste een stemming 75% van de aangesloten organen.
Houd er rekening mee dat sommige elementen van dit document onderwerp kunnen zijn van octrooirechten. ISO is niet verantwoordelijk voor het identificeren van dergelijke patenten.
ISO 23559 is ontwikkeld door de Technische Commissie ISO/TC 61, Kunststoffen, Subcommissie SC 11, Producten.
This second edition cancels and replaces the first edition (ISO 23559:2007) with a minor revision of the first edition (ISO 23559:2007) by introducing an additional specimen (for low strain) for the tensile impact test specified in Table 2.
ISO 23559-2011 – Testgids voor plastic films en thermoplastische films
voorstellen
The purpose of this international standard is to provide manufacturers and users with guidance for testing plastic film.
Although existing standards provide this guidance for many thin film products, these standards are very specific in terms of the materials covered and do not address many commercial films produced as mixtures or multilayer structures. In sommige gevallen, existing standards are limited to a single process technology for producing thin films.
It is also recognized that due to the numerous commercial processes used to produce thin films and the different processing parameters required for different materials, mixtures and/or structures, the general standardized concept of thin film sample preparation is not currently realistic. Aan de andere kant, it is possible to standardize sample preparation for clearly defined materials and manufacturing processes, but this is not within the scope or intent of this document.
Safety Statement – Persons using this document should be familiar with normal laboratory practices (if applicable). Dit document is niet bedoeld om alle veiligheidsproblemen weg te nemen, indien aanwezig, die verband houden met het gebruik ervan. It is the user’s responsibility to establish appropriate safety and health practices and ensure compliance with any regulatory requirements.
1 Toepassingsgebied
This international standard identifies specific test procedures to help manufacturers and users select and characterize single – or multilayer thermoplastic films. It is intended to provide a guide for films that do not have existing standards or specifications.
Note Due to the range of materials used and the variety of processes that can be used to produce various thin film structures, sample preparation is not covered in this document.
If an international standard exists for a particular film product, the requirements of that standard shall take precedence over this document.
There are many national, regional, and industry standards that address application-specific requirements. As this international standard is intended to provide general guidance, it is not within the scope of addressing these issues.
The importance and suitability of the data should be determined by the user.
ISO 23559-2011 – Testgids voor plastic films en thermoplastische films
2 Normatieve referentiedocumenten
Voor de toepassing van dit document zijn de volgende referentiebestanden vereist. Voor gedateerde referenties, alleen de geciteerde versie is van toepassing. Voor ongedateerde citaten, een nieuwe versie van het document waarnaar wordt verwezen (inclusief eventuele herzieningen) is van toepassing.
ISO 307, kunststoffen – polyamides – Determination of viscosity values
ISO 527-3 Kunststoffen – Bepaling van trekeigenschappen – Deel 3: Test conditions for films and sheets
ISO 1133-1, kunststoffen – Determination of melt mass flow (MFR) en smeltvolumestroom (MVR) of thermoplastics – Deel 1: Standard method
ISO 1183-1, kunststoffen – Determination of density of non-foam plastics – Deel 1: impregnation method, liquid pyronometer method and titration method
ISO 23559-2011 – Testgids voor plastic films en thermoplastische films
ISO 1183-2, kunststoffen – Determination of density of non-foam plastics – Deel 2: density gradient column method
ISO 1183-3, kunststoffen – Determination of density of non-foam plastics – Deel 3: Gas bottle method
ISO 2813, Verven en vernissen – Determination of mirror gloss of 20°, 60° en 85° niet-metalen verffilms
ISO 4589-1, kunststoffen – Determination of combustion behaviour by oxygen index – Deel 1: Guidance
ISO 4589-2, kunststoffen – Determination of combustion behaviour by oxygen index – Deel 2: ambient temperature test
ISO 4592, kunststoffen – films and sheets – determination of length and width
ISO 4593, kunststoffen – films and sheets – Determination of thickness by mechanical scanning
ISO 6383-1, kunststoffen – films and flakes – Determination of tear resistance – Deel 1: trouser tear method
ISO 6383-2, kunststoffen – films and sheets – Determination of tear resistance – Deel 2: Elmendorf method
ISO 7765-1, plastic films and sheets – Determination of impact resistance by the free fall method – Deel 1: step method
ISO 7765-2, plastic films and sheets – Determination of impact resistance by the free fall method – Deel 2: instrumental puncture test
ISO 23559-2011 – Testgids voor plastic films en thermoplastische films
ISO 8256, kunststoffen – Determination of tensile impact strength
ISO 8295, kunststoffen – films and sheets – Determination of coefficient of friction
ISO 8296, kunststoffen – films and sheets – determination of wetting tension
ISO 9773, kunststoffen – Determination of the burning behaviour of thin flexible vertical specimens in contact with a small flame ignition source
ISO 11357-2, kunststoffen – Differential scanning calorimetry (DSC) – Deel 2: Determination of glass transition temperature
ISO 11357-3 Kunststoffen – Differential scanning calorimetry (DSC) – Deel 3: Determination of melting and crystallization temperature and enthalpy
ISO 11443, kunststoffen – Determination of the fluidity of plastics using capillary tubes and slit die rheometers
ISO 11501, kunststoffen – films and sheets – Determination of dimensional changes in heating
ISO 11502, kunststoffen – films and sheets – Determination of resistance to adhesion
ISO 13468-1, kunststoffen – Determination of total light transmittance of transparent materials – Deel 1: single-beam instrument
ISO 13468-2, kunststoffen – Determination of total light transmittance of transparent materials – Deel 2: Double beam apparatus
ISO 14782, kunststoffen – Determination of fog in transparent materials
ISO 23559-2011 – Testgids voor plastic films en thermoplastische films
ISO 15105-1, kunststoffen – films and sheets – Determination of gas permeability – Deel 1: differential pressure method
ISO 15105-2, kunststoffen – films and sheets – Determination of gas permeability – Deel 2: isobaric method
ISO 15106-1 Kunststoffen – Films and sheets – Determination of water vapour transmittance – Deel 1: sensor method for humidity detection
ISO 15106-2 Kunststoffen – Films and sheets – Determination of water vapour transmittance – Deel 2: infrared detection sensor method
ISO 15106-3 Kunststoffen – Films and sheets – Determination of water vapour transmittance – Deel 3: electrolytic detection sensor method
ISO 15989, kunststoffen – films and sheets – Measurement of water contact Angle for corona treated films
IEC 60093, Test method for volume and surface resistivity of solid electrical insulating materials
IEC 60112, Verification of solid insulating materials and determination of comparative leakage marking index
IEC 60243-1, Electrical strength of insulating materials – Test methods – Deel 1: power frequency test
IEC 60250, recommended method for determining the dielectric constant and dielectric loss factor of electrical insulation materials at power, audio and radio frequencies, including meter wavelengths
ASTM D882, Standard test method for Tensile properties of thin plastic sheets
ASTM D5458, Standard Test method for Peel Adhesion of Stretched packaging Film
ASTM D5459, Standard Test Method for Longitudinal Elastic Recovery and Permanent Deformation and Stress Retention of Stretched Packaging films
ASTM D5748, Standard Test method for Resistance to protruding puncture of stretched packaging film
ASTM F88, Standard Test method for Sealing Strength of Flexible barrier materials
ASTM F1921, Standard Test Method for Thermal sealing Strength (thermal viscosity) of thermoplastic polymers and Blends Containing Flexible web sealing surfaces
ISO 23559-2011 – Testgids voor plastic films en thermoplastische films
3 termen en definities
Voor de doeleinden van dit document, de volgende termen en definities zijn van toepassing.
3.1 Thin Film
Films of nominal thickness not greater than 0.25 mm
Artikel opmerking 1: Although not specifically defined in ISO 472, de 0.25 mm limit is noted. ASTM D883 specifically defines thin films as ≤0.25 mm.
Opmerking 2: Sheets with a nominal thickness greater than 0.25 mm may be too hard to use test methods more suitable for thinner structures.
Alleen het standaardinformatiegedeelte is openbaar. Om de volledige inhoud te zien, u moet de standaard via de officiële kanalen aanschaffen.