ISO 16276-2-2007 “Evaluation and acceptance criteria for adhesion/cohesion (fracture strength) of protective coating systems to corrosion protective coatings on steel structures – Parte 2: cross-cut and X-cut tests”
introducere
ISO (Organizația Internațională pentru Standardizare) este o alianță globală a organismelor naționale de standardizare (organismele membre ISO). Elaborarea standardelor internaționale se realizează de obicei prin intermediul comitetelor tehnice ISO. Fiecare instituție membră interesată de un subiect pe care a fost înființat un comitet tehnic are dreptul de a fi reprezentată în respectivul comitet. Organizațiile internaționale guvernamentale și neguvernamentale care au legătură cu ISO sunt, de asemenea, implicate în această activitate. ISO lucrează îndeaproape cu Comisia Electrotehnică Internațională (IEC) în toate problemele de standardizare electrică.
Standardele internaționale sunt elaborate în conformitate cu regulile prevăzute în partea 2 din Directiva ISO/IEC.
Sarcina principală a comitetului tehnic este de a elabora standarde internaționale. Proiectul standardului internațional adoptat de Comitetul Tehnic va fi transmis organelor membre pentru vot. Publicarea ca standard internațional necesită aprobarea de cel puțin 75% a instituţiilor membre.
Vă rugăm să rețineți că anumite elemente ale acestui document pot face obiectul drepturilor de brevet. ISO nu este responsabil pentru identificarea unuia sau a tuturor acestor brevete.
ISO 16276-2-2007 “Evaluation and acceptance criteria for adhesion/cohesion (fracture strength) of protective coating systems to corrosion protective coatings on steel structures – Parte 2: cross-cut and X-cut tests”
ISO 16276-2 was developed by the European Committee for Standardization (CEN) Technical Committee CEN/TC 139, Vopsele și lacuri, in cooperation with the Technical Committee ISO/TC 35, Vopsele și Lacuri, Subcomisia SC 14, Coating Systems for the protection of Steel structures.
ISO 16276 constă din următoarele părți, with the general title “Corrosion protection of steel structures by protective coating systems – Evaluation and acceptance criteria for coating adhesion/cohesion (breaking strength) :
– Parte 1: Pull-out test
– Parte 2: Crosscutting test and X-cutting test
introduce
The main purpose of this part of ISO 16276 is to complement the ISO 12944 series in the field evaluation and acceptance criteria for coating adhesion/cohesion.
Note that this part of ISO 16276 is designed to evaluate transverse and X-cut tests for paint coatings on steel structures in the field. ISO 2409 prescribes crosscut testing and ASTM D 3359 prescribes a generic X-cut test without a note explaining the results or accepting or rejecting the criteria.
ISO 16276-2-2007 “Evaluation and acceptance criteria for adhesion/cohesion (fracture strength) of protective coating systems to corrosion protective coatings on steel structures – Parte 2: cross-cut and X-cut tests”
Breaking strength testing is often destructive and therefore requires maintenance work, the extent of which depends on the specifications and durability required for the protective paint coating.
The objective of this part of ISO 16276 is to minimize variability and achieve uniformity in practice when evaluating the break strength of bedliner coatings, and to establish acceptance/rejection criteria for such coatings. The method uses test equipment based on the principles of crosscutting and X-cutting.
1 Gamă
Această parte a ISO 16276 specifies that when cutting in the form of a rectangular lattice pattern (crosscut) or X (X-cut), the resistance rating program of the coating system is permeated into the coating and onto the substrate.
Această parte a ISO 16276 applies only to ratings that specify a crosscut or X-cut test method and the corresponding rating level.
Note that the characteristics of the coating can make it difficult to evaluate crosscut or X-cut test results.
ISO 16276-2-2007 “Evaluation and acceptance criteria for adhesion/cohesion (fracture strength) of protective coating systems to corrosion protective coatings on steel structures – Parte 2: cross-cut and X-cut tests”
Această parte a ISO 16276 also specifies suitable equipment and defines inspection areas, sampling plans and acceptance/rejection criteria.
It does not specify a rating for a particular coating system.
2 referințe normative
Următoarele fișiere de referință sunt necesare pentru aplicarea acestui document. Pentru referințe datate, se aplică doar versiunea citată. Pentru referințe nedatate, o nouă versiune a referinței (inclusiv orice revizuiri) se aplică.
ISO 2409-2006, vopsele și lacuri. Cross cutting test
ISO 12944-7, Vopsele și lacuri – Corrosion protection of steel structures through protective coating systems – Parte 7: Execution and supervision of paint work
ISO 12944-8, Vopsele și lacuri – Corrosion protection of steel structures by protective coating systems – Parte 8: Development of new work and maintenance specifications
ISO 19840, Vopsele și lacuri – Corrosion protection of steel structures by protective coating systems – Standard for measurement and acceptance of dry film thickness on rough surfaces
ASTM D 3359-02, Standard Test Method for Measuring Adhesion by Tape testing
ISO 16276-2-2007 “Evaluation and acceptance criteria for adhesion/cohesion (fracture strength) of protective coating systems to corrosion protective coatings on steel structures – Parte 2: cross-cut and X-cut tests”
3 Termeni și definiții
În sensul prezentului document, se aplică următorii termeni și definiții.
3.1 Forța de rupere
More than the force needed for the relay
– Between coatings or between coatings and substrate (adeziune) and/or
– Inside the coat (cohesive)
Notă 1: Această parte a ISO 16276 does not define a method for determining breaking strength (vezi ISO 16276-1).
3.2 Adeziune
Adhesion at the interface between a solid surface and another material caused by molecular forces
Notă 1: Adhesion should not be confused with cohesion.
[Sursă: ISO 4618:2006]
ISO 16276-2-2007 “Evaluation and acceptance criteria for adhesion/cohesion (fracture strength) of protective coating systems to corrosion protective coatings on steel structures – Parte 2: cross-cut and X-cut tests”
3.3 Cohesion
The force that binds the film together into a single entity
Notă 1: Cohesion should not be confused with adhesion.
[Sursă: ISO 4618:2006]
3.4 Coat
A continuous layer of coating material produced from a single application
[Sursă: ISO 4618:2006]
3.5 Clothes
A continuous layer formed by a single or multiple coating of a coating material onto a substrate
[Sursă: ISO 4618:2006]
3.6 Checking Areas
The specified area where the sampling plan has been applied can be the entire structure or a selected part of the structure
ISO 16276-2-2007 “Evaluation and acceptance criteria for adhesion/cohesion (fracture strength) of protective coating systems to corrosion protective coatings on steel structures – Parte 2: cross-cut and X-cut tests”
Doar secțiunea de informații standard este publică. Pentru a vedea conținutul complet, trebuie să achiziționați standardul prin canalele oficiale.