А Префаце
ИСО (Међународна организација за стандардизацију) је глобални савез националних тела за стандардизацију (Тела чланица ИСО). Развој међународних стандарда се обично спроводи преко ИСО техничких комитета. Свака институција чланица заинтересована за предмет за који је основан технички комитет има право да буде заступљена у комитету. У овај посао су укључене и владине и невладине међународне организације које су у вези са организацијама за стандардизацију. ИСО блиско сарађује са Међународном електротехничком комисијом (ИЕЦ) о свим питањима електричне стандардизације.

The procedures used to develop this document as well as those used for further maintenance are described in Part 1 ИСО/ИЕЦ директиве. Нарочито, треба обратити пажњу на различите критеријуме одобрења који су потребни за различите типове ИСО докумената. Овај документ је састављен у складу са уређивачким правилима Дел 2 ИСО/ИЕЦ директиве (види исо.орг/дирецтивес).

ИСО 1514-2016 “Боје и лакови – Standard Sample for testing”

Please note that certain contents of this document may be subject to patent rights. ИСО није одговоран за идентификацију било ког или свих таквих патентних права. Details of any patent rights identified during the preparation of the document will be in the introduction and/or in the list of patent claims received by ISO (see iso.org/patents).

Any trade names used in this document are provided as information for the convenience of the user and do not constitute an endorsement.

For conformity assessment related ISO specific terminology and express the meaning of the specification, as well as the relevant ISO in technical barriers to trade (ТБТ) adhere to the principle of the world trade organization (WTO) in the information, please refer to the following URL:iso.org/iso/foreword.html.

The committee responsible for this document is ISO/TC 35, Боје и лакови, Subcommittee SC 9, General test methods for paints and varnishes.

Fifth edition to cancel and replace the fourth edition (ИСО 1514:2004), which is revised on technology, made the following changes:

А) the method of preparation of the zinc phosphate and chromate treatment, chromate conversion coating and acid chromium, remove;

Б) to modify the following materials: coil coating board, plastic board, glass fiber reinforced plastic composite board, carbon fiber reinforced plastics (GRP) composite panels (CFP);

ИСО 1514-2016 “Боје и лакови – Standard Sample for testing”

ц) The original annex B on the characteristics of zinc and zinc alloy coatings has been deleted;

d) A new annex B is added to the universal substrate surface board;

e) Normative references have been updated.

Увод
For many of the most widely used test methods for paints and varnish, the type of panel used and the particular way in which it is prepared for use can greatly affect the test results. As carefully as possible before painting, дакле, standardization of panels and used for preparation procedure is very important.

It is not possible to include in international standards all the types of panels and preparations required for paint testing

This international standard describes preparation procedures that are known to be reproducible and provides additional guidance in cases where there may still be doubt due to a lack of international uniformity of procedures.

ИСО 1514-2016 “Боје и лакови – Standard Sample for testing”

1 Обим
This international standard specifies several types of standard panels and describes procedures for preparing them before painting. These standard panels are used for general test methods for paints, varnishes and related products (see Annex B).

2 Normative references
The following documents are referred to normatively in whole or in part in this document and are required for their application. За датиране референце, примењује се само наведена верзија. For undated references, the references of the new version (including any amendment) примењује.

ИСО 1268 (all components), fiber-reinforced plastics — Method for producing test plates

ИСО 2409, Боје и лакови — Cross cut test

ИСО 2808, Боје и лакови — Determination of film thickness

ИСО 1514-2016 “Боје и лакови – Standard Sample for testing”

ИСО 4287, geometrical product specifications (GPS) – surface texture: profile method, terms, definitions, and surface texture parameters

ИСО 8336, fibre cement plates-product specifications and test methods

ИСО 11949, cold reduction electrolytic tin plate

ИН 520, Gypsum plasterboard – Definitions, requirements and test methods

ИН 622 (all components), fiberboard — Спецификација

ИН 1396, Aluminium and aluminium alloys – coiled-sheet and strip for general applications – Спецификација

ИН 10205, cold reduction blackboards in coil form for the production of tinplate or electrolytic chromium/chromium oxide coated steels

ИСО 1514-2016 “Боје и лакови – Standard Sample for testing”

ИН 13523-1, the coil coating metal – методе испитивања – part 1: thin film thickness

ИН 13523-22, coil coated metals – Test methods – Парт 22: Chromatic aberration – Visual comparison

ИН 15283-2, fiber-reinforced plasterboard – definitions, requirements and test methods – part 2: gypsum fiberboard

ИН 16245-1, fiber-reinforced plastic composites – Statements on properties of raw materials – Парт 1: General requirements

Јавно је доступна само стандардна информативна компонента. Да бисте видели цео садржај, мораћете да купите стандарде путем формалних канала.