предговор
ИСО (Међународна организација за стандардизацију) је глобална федерација националних тела за стандардизацију (Тела чланица ИСО). Развој међународних стандарда се обично спроводи преко ИСО техничких комитета. Each member group interested in a subject on which a technical committee has been established has the right to be represented on the Committee. International, governmental and non-governmental organizations in liaison with ISO are also involved in this work. ИСО блиско сарађује са Међународном електротехничком комисијом (ИЕЦ) о свим питањима електричне стандардизације.

Међународни стандарди се израђују у складу са правилима датим у ч 2 ИСО/ИЕЦ директиве.

The main task of the technical committee is to set international standards. The draft international standards adopted by the Technical Committee will be circulated to member bodies for voting. Публикација као међународни стандард захтева одобрење са најмање гласова 75% of the member body.

Имајте на уму да неки елементи овог документа могу бити предмет патентних права. ИСО није одговоран за идентификацију било ког или свих таквих патената.

ИСО 23559 was developed by the Technical Committee ISO/TC 61, Plastics, Subcommittee SC 11, Производи.

This second edition cancels and replaces the first edition (ИСО 23559:2007) by slightly revising the first edition (ИСО 23559:2007) by introducing an additional specimen (for low strain) for the tensile impact test specified in Table 2.

ИСО 23559-2011 Guide for testing plastic films and sheet thermoplastic Films

увести
This international standard is intended to provide manufacturers and users with guidance for testing plastic film.

Although existing standards provide this guidance for many thin film products, they are very specific in terms of the materials covered and do not address many commercial films produced as mixtures or multilayer structures. In some cases, existing standards are limited to a single process technology for producing thin films.

It is also recognized that the general standardized concept of film sample preparation is not currently realistic due to the numerous commercial processes used to produce films and the different processing parameters required for different materials, mixtures and/or structures. С друге стране, it is possible to standardize sample preparation for clearly defined materials and manufacturing processes, but this is not within the scope or intent of this document.

Safety Statement – Persons using this document should be familiar with normal laboratory practices (if applicable). This document is not intended to address all security concerns, ако их има, повезана са његовом употребом. It is the user’s responsibility to establish appropriate safety and health practices and ensure compliance with any regulatory requirements.

ИСО 23559-2011 Guide for testing plastic films and sheet thermoplastic Films

1 Обим примене
This international standard identifies specific testing procedures to assist manufacturers and users in selecting and characterizing single – or multilayer thermoplastic films. It aims to provide a guide for films that do not have existing standards or specifications.

Note Due to the range of materials used and the variety of processes that can be used to produce various thin film structures, sample preparation is not covered in this document.

If an international standard exists for a particular film product, the requirements of that standard shall take precedence over this document.

There are many national, regional, and industry standards that address application-specific requirements. Since this international standard is intended to provide general guidance it is not within the scope of addressing these issues.

The importance and applicability of the data should be determined by the user.

2 Normative reference files
The following reference files are required for the application of this file. За датиране референце, citation-only versions apply. За цитате без датума, the most recent version of the referenced document (including any amendments) примењује.

ИСО 307, Plastics – polyamides – Determination of viscosity values

ИСО 527-3, пластике – Determination of tensile properties – Парт 3: Test conditions for films and sheets

ИСО 1133-1, пластике – Determination of melt mass flow (МФР) и запремински ток растопа (МВР) of thermoplastics – Парт 1: Standard method

ИСО 1183-1, пластике – Determination of the density of non-foamed plastics – Парт 1: immersion method, liquid gravity flask method and titration method

ИСО 1183-2, пластике – Determination of the density of non-foamed plastics – Парт 2: density gradient column method

ИСО 1183-3, пластике – Determination of the density of non-foamed plastics – Парт 3: Gas specific gravity flask method

ИСО 2813, Боје и лакови – Determination of the specular gloss of 20°, 60° и 85° неметалне боје

ИСО 4589-1, пластике – Determination of combustion behaviour by oxygen index – Парт 1: Guide

ИСО 4589-2, пластике — Determination of combustion behaviour by oxygen index — Парт 2: ambient temperature test

ИСО 4592, пластике – films and sheets – determination of length and width

ИСО 4593, Plastics – films and sheets – Determination of thickness by mechanical scanning

ИСО 6383-1, пластике – films and sheets – Determination of tearing resistance – Парт 1: pant type tearing method

ИСО 6383-2, пластике – films and sheets – Determination of tearing resistance – Парт 2: Elmendorf method

ИСО 7765-1, plastic films and sheets – Determination of impact resistance by the free-fall method – Парт 1: Step method

ИСО 7765-2, Plastic films and sheets – Determination of impact resistance by the free fall method – Парт 2: Instrumental puncture test

ИСО 8256, Plastics – Determination of tensile impact strength

ИСО 8295, Plastics – films and sheets – Determination of coefficient of friction

ИСО 8296, Plastics – films and sheets – determination of wetting tension

ИСО 9773, пластике – Determination of the combustion behaviour of thin flexible vertical specimens in contact with a small flame ignition source

ИСО 11357-2, пластике — Differential scanning calorimetry (DSC) — Парт 2: Determination of glass transition temperature

ИСО 11357-3, пластике — Differential scanning calorimetry (DSC) — Парт 3: Determination of melting and crystallization temperature and enthalpy

– ИСО 11443, Plastics – Determination of the fluidity of plastics using capillaries and slit die head rheometers

ИСО 11501, пластике – films and sheets – Determination of dimensional changes in heating

ИСО 11502, пластике – films and sheets – Determination of adhesion resistance

ИСО 13468-1, пластике – Determination of total light transmittance of transparent materials – Парт 1: single beam instrument

ИСО 13468-2, Plastics — Determination of total light transmittance of transparent materials — Парт 2: Double beam instrument

ИСО 14782, Plastics — determination of fog in transparent materials

ИСО 15105-1, пластике – films and sheets – Determination of gas transmittance – Парт 1: differential pressure method

ИСО 15105-2, пластике – films and sheets – Determination of gas permeability – Парт 2: isobaric method

ИСО 15106-1, пластике – films and sheets – Determination of water vapour transmittance – Парт 1: Humidity detection sensor method

ИСО 15106-2, пластике – films and sheets – Determination of water vapour transmittance – Парт 2: Infrared detection sensor method

ИСО 15106-3, пластике – films and sheets – Determination of water vapour transmittance – Парт 3: electrolytic detection sensor method

ИСО 15989, Plastics – films and sheets – Measurement of water contact angles for corona treated films

ИЕЦ 60093, Test method for volume and surface resistivity of solid electrical insulating materials

ИЕЦ 60112, Verification and comparison of solid insulating materials – Determination of leakage trace index

ИЕЦ 60243-1, Electrical strength of insulating materials – Test methods – Парт 1: power frequency test

ИЕЦ 60250, recommended method for determining the dielectric constant and dielectric loss factor of electrical insulating materials at power, audio and radio frequencies (including meter wavelengths)

ASTM D882, Standard Test Method for Tensile Properties of Thin plastic Sheets

ASTM D5458, Standard Test method for Peel Adhesion of Stretched Packaging Film

ASTM D5459, Standard Test Method for Longitudinal Elastic Recovery and Permanent Deformation and Stress Retention of Stretched Packaging Films

ASTM D5748, Standard Test method for Resistance to Protruding Puncture of Stretched Packaging films

ASTM F88, Standard Test Method for Seal Strength of Flexible Barrier Materials

ASTM F1921, Standard Test Method for Thermal Sealing Strength (Thermal Viscosity) of Thermoplastic polymers and Blends Containing Flexible Web Sealing Surfaces

3 Terms and Definitions
For the purposes of this document, the following terms and definitions apply.

3.1 Thin Film

Films of nominal thickness not greater than 0.25 мм

Ентри Ноте 1: Although not specifically defined in ISO 472, the 0.25mm limit is noted. ASTM D883 specifically defines thin films as ≤ 0.25mm.

Белешка 2 Sheets with nominal thickness greater than 0.25mm May be too hard to use a test method more suitable for thinner structures.

Јаван је само одељак са стандардним информацијама. Да бисте видели цео садржај, морате купити стандард преко званичних канала.