ISO 178-2019 – Plastiklerin bükülme özelliklerinin belirlenmesi
Bir Önsöz
ISO (Uluslararası Standardizasyon Örgütü) ulusal standart kuruluşlarının küresel bir ittifakıdır (ISO üyesi kuruluşlar). Uluslararası standartların geliştirilmesi genellikle ISO teknik komiteleri aracılığıyla yürütülür.. Teknik komite oluşturulmuş bir konu ile ilgilenen her üye kuruluşun komitede temsil edilme hakkı vardır.. Standardizasyon kuruluşlarıyla irtibat halinde olan hükümet ve sivil toplum uluslararası kuruluşları da bu çalışmaya katılmaktadır.. ISO, Uluslararası Elektroteknik Komisyonu ile yakın işbirliği içinde çalışır. (IEC) elektriksel standardizasyonla ilgili tüm konularda.
Bu belgeyi geliştirmek için kullanılan prosedürlerin yanı sıra daha ileri bakım için kullanılan prosedürler Bölümde açıklanmıştır. 1 ISO/IEC Direktifi. Özellikle, Farklı türdeki ISO belgeleri için gerekli olan farklı onay kriterlerine dikkat edilmelidir.. Bu belge Bölüm yazım kurallarına uygun olarak hazırlanmıştır. 2 ISO/IEC Direktifi (iso.org/direktiflere bakın).
ISO 178-2019 – Plastiklerin bükülme özelliklerinin belirlenmesi
Lütfen bu belgenin belirli içeriklerinin patent haklarına tabi olabileceğini unutmayın.. ISO, bu tür patent haklarının herhangi birinin veya tamamının tanımlanmasından sorumlu değildir.. Belgenin hazırlanması sırasında belirlenen patent haklarının ayrıntıları girişte ve/veya ISO tarafından alınan patent talepleri listesinde yer alacaktır. (iso.org/patents'e bakın).
Any trade names used in this document are provided as information for the convenience of the user and do not constitute an endorsement.
Gönüllü, related standards and conformity assessment related ISO specific and express the meaning of terminology as well as in relevant ISO technical barriers to trade (TBT) adhere to the principle of the world trade organization (WTO) information, please refer to the following URL:iso.org/iso/foreword.html.
This document is prepared by ISO/TC 61, Plastikler, Alt Komite SC 2, Mechanical Properties.
ISO 178-2019 – Plastiklerin bükülme özelliklerinin belirlenmesi
The sixth edition eliminates and replaces the technically revised fifth edition (ISO 178:2010). It also incorporates amendments to ISO 178:2010 / Amd.1:2013. Compared with the previous edition, the main changes are as follows:
– Differentiation of calibration requirements according to test type;
– Introduction of deflectometer;
– Resumption of compliance correction procedures;
— A new annex D has been added, showing the relationship between tensile modulus and bending modulus.
Any feedback or questions regarding this document should be directed to the user’s national standards body. A full list of these agencies can be found at iso.org/members.html.
ISO 178-2019 – Plastiklerin bükülme özelliklerinin belirlenmesi
1 Kapsam
This document specifies a method for determining the bending properties of rigid and semi-rigid plastics under specified conditions. The preferred sample selection was defined, but parameters for the size of the standby sample were included for use where appropriate. Includes a series of test speeds.
This method is used to study the bending behavior of the specimen and to determine the bending strength, bending modulus and other aspects of the bending stress/strain relationship under defined conditions. It is suitable for free support beams loaded at mid-span (three-point loading test).
The method is applicable to the following material ranges:
– Thermoplastic forming, extrusion and casting materials, including filled and reinforced compounds in addition to unfilled types; Rigid thermoplastic sheet;
– Thermoset molding materials, including filling and reinforcing compounds; Thermoset sheet.
According to ISO 10350-1[5] ve ISO 10350-2[6], this document applies to fiber reinforced compounds with fiber length ≤7.5 mm before processing. For fiber length > 7.5 mm long fiber reinforcement (laminat), ISO'ya bakın 14125[7].
This method is generally not applicable to rigid porous materials or sandwich structures containing porous materials. Bu durumda, ISO 1209-1[3] and/or ISO 1209-2[4] kullanılabilir.
Not 1 For certain types of textile fiber reinforced plastics, a four-point bending test is used. This is described in ISO 14125.
ISO 178-2019 – Plastiklerin bükülme özelliklerinin belirlenmesi
The method is carried out using specimens that may be molded to specified dimensions, processed from the central portion of a standard multipurpose specimen (ISO'ya bakın 20753) or processed from finished or semi-finished products, such as moulds, laminated plates or extruded or cast plates.
This method specifies the selected size of the sample. Tests performed on specimens of different sizes or prepared under different conditions can yield incomparable results. Other factors, such as the speed of the test and the conditioning of the specimen, can also affect the results.
Not 2 Especially for injection molded semi-crystalline polymers, the thickness of the oriented skin layer depends on the forming conditions and also affects the bending performance.
This method is not suitable for the determination of design parameters, but it can be used for material testing and quality control testing.
ISO 178-2019 – Plastiklerin bükülme özelliklerinin belirlenmesi
2 Normatif referanslar
Aşağıdaki belgelere, içeriklerinin bir kısmı veya tamamı bu belgenin gerekliliklerini oluşturacak şekilde metinde atıfta bulunulmaktadır.. Tarihli referanslar için, yalnızca alıntı yapılan versiyon geçerlidir. Tarihsiz referanslar için, referansın yeni versiyonu (herhangi bir revizyon dahil) geçerlidir.
ISO 291, Plastikler — Standard atmosphere for conditioning and testing
ISO 293, Plastikler — Compression molding of thermoplastic material specimens
ISO 294-1:2017, Plastikler. Injection molding of thermoplastic material samples. Parça 1: General principles and molding of general-purpose and bar specimens
ISO 295, Plastikler — Compression molding of specimens of thermoset materials
ISO 2602, Statistical interpretation of test results-mean estimates-confidence intervals
ISO 2818, plastik — Preparation of specimens by machining
ISO 750-1, Metallic materials — Calibration and verification of static uniaxial testing machines — Parça 1: Tensile/compression testing machines — Calibration and verification of force measurement systems
ISO 9513, Metallic materials — Calibration of extensiometer systems for use in uniaxial testing
ISO 10724-1, Plastikler — Injection molding of thermoset powder molded plastics (PMC) specimens — Parça 1: General principles and molding of multipurpose specimens
ISO 16012, Plastikler — Determination of linear dimensions of specimens
ISO 20753, Plastikler — Specimen
ISO 178-2019 – Plastiklerin bükülme özelliklerinin belirlenmesi
3 Terms, definitions and symbols
Bu belgenin amaçları doğrultusunda, aşağıdaki terimler ve tanımlar geçerlidir.
ISO ve IEC, standardizasyon için terminoloji veritabanlarını aşağıdaki adreslerde tutar:
– ISO çevrimiçi tarama platformu: iso.org/obp adresinde mevcuttur
– IEC Elektronik Ansiklopedisi: elektropedia.org'da mevcut
3.1 Test speed v
The relative rate of movement between the sample support and the loaded edge
Not 1: It is expressed in millimeters per minute (mm/dak).
3.2 Bending stress σf
Nominal stress on the outer surface of the specimen at the middle span
Not 1: It is calculated based on the relationship given in Equation (5).
Not 2: It is expressed in megapascals (MPa).
3.3 Bending stress σFB at fracture
Bending stress of the specimen at fracture
Not 1: It is expressed in megabascals (MPa).
Not 2: See Figure 1, curves a and b.
ISO 178-2019 – Plastiklerin bükülme özelliklerinin belirlenmesi
3.4 Flexural strength σfM
Maximum bending stress sustained by the specimen during bending test (3.2)
Not 1: It is expressed in megabascals (MPa).
Not 2: See Figure 1, curves a and b.
3.5 Bending stress σ under conventional deflection
Bending stress at conventional deflection, sC (3.7)
Not 1: It is expressed in megabascals (MPa).
Not 2: See also Figure 1, Curve c.
3.6 Deflection s
The distance of the top or bottom surface of the mid-span specimen from its original position during bending
Not 1: It is expressed in millimeters (mm).
3.7 Conventional deflection sC
The deflection (3.6) is equal to 1.5 times the sample thickness H
Not 1: It is expressed in millimeters (mm).
ISO 178-2019 – Plastiklerin bükülme özelliklerinin belirlenmesi
Not 2: Using a 16-h span L, the conventional deflection corresponds to a flexure strain of 3.5% (3.8).
3.8 Bending strain εf
Nominal fractional change in wafer length on the outer surface of the specimen at the mid-span
Not 1: It is expressed as a dimensionless ratio or percentage (%).
Açıklama 2: It is calculated from the relationship given in equations (6) Ve (7).
Figür 1 — Typical curves of bending stress σf versus bending strain εf and deflection s
| Curve a | A specimen that breaks before yielding |
| Curve b | The specimen that gives the maximum value then breaks before the conventional deflection, sC |
| Curve c | Specimens that neither give a maximum nor break before the conventional deflection, sC |
ISO 178-2019 – Plastiklerin bükülme özelliklerinin belirlenmesi
3.9 Bending strain εFB at fracture
Bending strain of the specimen at fracture
Not 1: It is expressed as a dimensionless ratio or percentage (%).
Not 2: See Figure 1, curves a and b.
3.10 Bending strain εfM under bending strength
Bending strain under maximum bending stress
Not 1: It is expressed as a dimensionless ratio or percentage (%).
Not 2: See Figure 1, curves a and b.
3.11 Flexural modulus Flexural modulus Ef
Ratio of the stress difference σf2 − σf1 to the corresponding strain difference εf2 (= 0,002 5) − εf1 (= 0,000 5)
Not 1: It is expressed in megabascals (MPa).
Açıklama 2: The bending modulus is only an approximation of Young’s modulus.
Not 3: Please refer to Equation (9).
ISO 178-2019 – Plastiklerin bükülme özelliklerinin belirlenmesi
3.12 Rigid plastics
Plastics with an elastic modulus (3.11) in bending hinges or, if not applicable, in stretching, greater than 700 MPa under the given conditions
[Kaynak: ISO 472:2013, 2.884, değiştirilmiş — entry comments have been omitted.
3.13 Semi-rigid plastics
A plastic with an elastic modulus in a bending hinge (3.11) veya, if this modulus is not applicable, between 70 MPa and 700 MPa under tension for the given conditions
[Kaynak: ISO 472:2013, 2.909, değiştirilmiş – entry comments have been omitted.
3.14 Span L between sample supports
The distance between the contact point between the specimen and the specimen holder
Not 1: It is expressed in millimeters (mm).
Not 2: See Figure 2.
ISO 178-2019 – Plastiklerin bükülme özelliklerinin belirlenmesi
3.15 Bending strain rate r
Rate of increase in bending strain (3.8) test boyunca
Açıklama 1: It is expressed as a percentage per minute (% ⋅ min−1).
Yalnızca standart bilgi bileşeni kamuya açıktır. İçeriğin tamamını görmek için, standartları resmi kanallardan satın almanız gerekecek.